BMW 7_aya the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and methods of operation
3. Settings and routine maintenance of the car
4. Engine
5. Cooling systems of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
6.1. General information and security measures
6.2. Power supply system of petrol engines
6.2.1. Principles of functioning of a control system of the petrol engine
6.2.2. Removal and installation of the case of the air cleaner
6.2.3. Removal and installation of a branch pipe between a flowmeter of air and the case of a butterfly valve
6.2.4. Removal and installation of the case of a throttle, replacement of its laying
6.2.5. Removal and installation of the IAC valve
6.2.6. Removal and installation of the fuel distributive highway and injectors
6.2.7. Replacement of the regulator of pressure of fuel
6.2.8. Removal and installation of the fuel pump
6.2.9. Removal and installation of sensors of a reserve of fuel
6.2.10. Removal and installation of the fuel tank
6.2.11. Removal and installation of a fuel jellied mouth
6.3. Power supply system of diesel engines
6.4. Systems of release and decrease in toxicity of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Cardan and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
14. Onboard electric equipment
15. Schemes of electric equipment



6-2-5-snyatie-i-ustanovka-klapana-iac.html

6.2.5. Removal and installation of the IAC valve

Models with the M52 engine

 PERFORMANCE ORDER

  1. Switch off ignition. Remove the air cleaner case (see the Section Removal and installation of the case of the air cleaner).
  2. Remove cases of butterfly valves (see the Section Removal and installation of the case of a throttle, replacement of its laying).

Do not disconnect cables and hoses of heating of a butterfly valve.


  1. Pick up the directing phone of the probe of level of motive oil (1). Wring out a clamp, separate the socket, turn out two bolts (2) and disconnect the IAC valve.
  1. Remove laying (1) and a rubber collar (2). Weaken a collar (3) and disconnect a hose.
  1. Installation is made upside-down. Replace laying. In conclusion check idling turns.

Models with the M52TU engine

 PERFORMANCE ORDER

  1. 1 on 6Perform the operations described in paragraphs with Sections Removal and installation of the case of a throttle, replacement of its laying.

Do not separate D/V sockets of pressure and temperature of motive oil.


  1. Turn out a bolt (1) of fastening of a box of an electrical wiring, bolts (2) holders of the valve (3) IAC and take out the IAC valve from an inlet collector together with an arm.
  1. Remove the valve (2) IAC from the fixing rubber element (4). Laying (1) between the IAC valve and the inlet pipeline is subject to replacement. But it is necessary to install consolidation at repeated installation not on the IAC valve, and at first in an inlet collector.
  1. Installation is made upside-down.

Models with M60 and M62 engines

 PERFORMANCE ORDER

  1. Perform the operations described in paragraphs with 1 on 3 Sections Removal and installation of the case of a throttle, replacement of its laying.
  1. Hang out fastening (1) and take out the IAC valve.
  1. Installation is made upside-down. For ensuring tightness sealing rings on the case of a throttle and on the IAC valve have to be pure and without damages. In case of damage of sealing rings they should be replaced. At installation first of all it is necessary to establish a sealing ring on a flange of a butterfly valve.


"previous page
6.2.4. Removal and installation of the case of a throttle, replacement of its laying
following page"
6.2.6. Removal and installation of the fuel distributive highway and injectors