BMW 7_aya the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and methods of operation
3. Settings and routine maintenance of the car
4. Engine
5. Cooling systems of the engine, heating, ventilation and air conditioning
5.1. Engine cooling system
5.2. Systems of heating, ventilation and air conditioning
5.2.1. General information
5.2.2. Removal and installation of a heater
5.2.3. Removal and installation of a radiator of a heater
5.2.4. Removal and installation of fans and resistor assemblies
5.2.5. Removal and installation of the additional water pump and water valve
5.2.6. Removal and installation of deflectors of systems of heating, ventilation and To/in
5.2.7. Removal and installation of the K/V compressor
5.2.8. Removal of other components of the K/V system
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Cardan and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
14. Onboard electric equipment
15. Schemes of electric equipment



5-2-1-obshhaya-informaciya.html

5.2.6. Removal and installation of deflectors of systems of heating, ventilation and To/in

Side deflectors

PERFORMANCE ORDER

Before removal of the left deflector perform the following operations: Remove a wooden level and separate the socket of switches of illumination of the dashboard and adjustment of an inclination of headlights; The Wooden level Turn out top (without pro-masonry washer) of and lower (with a pro-masonry washer) bolts of fastening and remove the left ware box.

Unhook a cable of an unblocking of the parking brake. Fixture of the left ware box Before removal of the right deflector perform the following operations: Open and incline a ware box down. Turn out screws and unbend the top part of facing of a ware box; Clamps of the left side deflector Separate sockets of the switch and the lighting lamp of a ware box and remove facing.

Close the deflector. Take away sound insulation (1) a little down to provide access to both clamps of the deflector. Wring out at first one, then second clamp of the deflector. That the wrung-out clamp was not blocked, establish a thin wide plate (adaptation No. 00 9 300) between the lower edge of the deflector and its nest. Separate an air supply sleeve from the deflector. Top and the central deflectors At removal of deflectors of models with the integrated system of heating and To/in pass to paragraph 6. In paragraphs with 1 on 5 preparatory operations at removal of deflectors of models with adjustment of the To/in system are described.

ORDER of PERFORMANCE Turn out the screw (1), raise the panel of facing (2) of a foot well of the forward passenger a little and remove it the movement on yourself (3). Turn out bolts (1) and take out rivets (2 and 3) of fastening of the lower panel of the right ware box. Delay facing forward, remove and separate the buzzer socket. Open and incline a ware box down. Turn out screws and unbend the top part of facing of a ware box (see an illustration). Separate sockets of the switch and the lighting lamp of a ware box and remove facing.

Take out rivets, movement separate the socket up and remove side facing panels. Take out from fastenings an air duct in a foot well. Unhook a cable of the drive of the gate of adjustment of air temperature. Enter adaptation No. 00 9 300 between the top deflector (1) and a frame (2). Consistently unclench clamps of the top lattice in points (1-3), pick up and remove a lattice. Turn out screws. Pick up and remove a frame snuffled ventilation, separate the KL socket (1). Turn out the screw (1) and take out a pro-rate (2).

Close the deflector, wring out it a little up and enter both devices No. 00 9 300 below into a crack between the deflector and the dashboard, so to wring out clamps (1). Similarly wring out the top clamps. Push both hands in an aperture of the top deflector and push out the central deflectors from within. Installation is made upside-down. The deflector in a back part of salon Depending on a complete set under the deflector can be installed the control panel of a heater or a decorative level.

Anyway removal of the deflector is made equally. The PERFORMANCE ORDER wring out from each other the deflector (1) and the control panel of a heater (2) A little. Wring out clamps and bring the control panel of a heater at first out of the top directing groove, then delay the deflector up and remove the control panel. Displace the deflector down at a size about 35 mm and bring out of deepenings in the directing grooves.

For installation bring the deflector (1) to deepenings in the middle of the directing grooves and insert up to the end the movement up. After that establish a decorative level or the control panel of a heater.


"previous page
5.2.5. Removal and installation of the additional water pump and water valve
following page"
5.2.7. Removal and installation of the K/V compressor