BMW 7_aya the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and methods of operation
3. Settings and routine maintenance of the car
4. Engine
5. Cooling systems of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Cardan and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
13.1. External equipment and body elements
13.2. Equipment of salon
13.2.1. Removal and installation of window regulators
13.2.2. Removal and installation of finishing and sound insulation of a forward door
13.2.3. Removal and installation of finishing and sound insulation of a back door
13.2.4. Removal and installation of panels of finishing of racks of a body and ceiling
13.2.5. Removal and installation of finishing of the dashboard
13.2.6. Removal and installation of the shelf behind a back seat and blinds of back glass
13.2.7. Removal and installation of overlays of thresholds of doors
13.2.8. Removal and installation of elements of finishing of the luggage compartment and its cover
13.2.9. Removal and installation of front seats
13.2.10. Removal and installation of a back seat
13.2.11. Removal and installation of seat belts
13.2.12. Removal and installation of a cover of the top hatch
14. Onboard electric equipment
15. Schemes of electric equipment



13-2-4-snyatie-i-ustanovka-panelejj-otdelki-stoek-kuzova-i-potolka.html

13.2.4. Removal and installation of panels of finishing of racks of a body and ceiling

A rack

 PERFORMANCE ORDER

  1. On models with a safety cushion in A rack:
  • Remove a protective fringing on an overlay of a rack and take out a clip (1);
  • Turn out a bolt (1).

At installation check correctness of provision of a clip (2).

  1. Remove an overlay of a forward rack the movement inside and up.
  1. Installation is made upside-down. Replace the damaged clamps and caps.
  1. On models with a safety cushion in a rack A soft uvula (1) of a cap (2) has to be turned towards a safety cushion (3), otherwise the clip (4) can damage a pillow.

B rack, lower section of finishing

 PERFORMANCE ORDER

  1. Remove overlays of thresholds of forward and back doors (see the Section Removal and installation of overlays of thresholds of doors).
  2. Move a seat to extreme forward situation.
  1. Partially remove a protective fringing from an overlay of an average rack. Wring out clamps of the lower panel of finishing of an average rack by the movement inside (1) and remove the panel of finishing by the movement (2) down.
  1. Installation is made upside-down. Replace the damaged clamps and caps.

B rack, top section of finishing

 PERFORMANCE ORDER

  1. Remove the lower panel of finishing of a rack of B.
  1. Turn out a bolt of fastening of a seat belt of forward sitting.
  1. Remove a protective fringing of the top section of finishing of an average rack. Wring out clamps of the lower section of finishing of a rack by B movement inside (1) and remove it the movement (2) down.
  1. Installation is made upside-down. Replace the damaged clamps and caps.

Rack of C

 PERFORMANCE ORDER

  1. Disconnect a plafond of the back lamp, remove it the movement up and separate the socket.
  1. On models with a safety cushion in a rack of C (with a badge 1) turn out screws (2) and remove facing (3) by the movement inside and up.
  1. On models without safety cushion in a rack of C turn out bolts and remove facing by the movement inside and up.
  1. When replacing the panel of finishing remove a noise isolation (1) from the old panel and paste it on the new panel.

Ceiling

 PERFORMANCE ORDER

  1. Remove all top hand-rail and finishing of all racks of a body.
  2. Remove the right front seat (see the Section Removal and installation of front seats).
  3. Uncover the top hatch Section Removal and installation of a cover of the top hatchHead Kuzov(see )
  1. Remove a sun-protection peak and lamps (1) of illumination of a cosmetic mirror. Separate sockets, remove slips from a support and the hinge and turn out screws. Slightly extend a wire and separate the illumination socket.
  1. Turn out bolts and remove a protective framework. When replacing if necessary replace nuts in finishing of a ceiling.
  1. Remove a plafond of the main saloon lamp and separate the socket.
  1. Pick up and take out a cap, separate the socket.
  1. Rearrange a back of the left forward sitting in extreme back situation.
  1. On models to 05.1997 g of the issue pick up and take out clamps (1) with left and on the right side. Squeeze out finishing of a ceiling of metal pads by the movement back and remove it, shifting towards the right back door. On models from 05.1997 g of the issue squeeze out finishing of a ceiling of metal pads by the movement back and remove, shifting towards the right back door.
  1. Installation is made upside-down. Insert the device No. 51 4 000 in the basis of a covering of a ceiling and record an adhesive tape on a textile basis (2). On models with the block of connection of automobile phone, whenever possible, carry out over the block of connection of automobile phone (1).
  1. Press finishing (1) of a ceiling to adaptation No. 51 4 000 by the movement up, move against the stop forward and fix. Remove adaptation No. 51 4 000 and wipe back glass.
1 — Finishing of a ceiling
2 — the Sealing profile
3 — a glue Strip
4 — Back glass
5 — the Box of switches
6 — the antenna Basis
7 — the Antenna
8 — the Adhesive tape on a textile basis


"previous page
13.2.3. Removal and installation of finishing and sound insulation of a back door
following page"
13.2.5. Removal and installation of finishing of the dashboard