BMW 7_aya the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and methods of operation
3. Settings and routine maintenance of the car
4. Engine
5. Cooling systems of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Cardan and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
12.1. General information, recommendations and security measures
12.2. Forward suspension bracket
12.3. Back suspension bracket
12.4. EDC system
12.5. Steering
12.5.1. Principle of work of GUR
12.5.2. Removal and installation of a steering wheel, block of a safety cushion and its contact ring
12.5.3. Removal and installation of casings of a steering column
12.5.4. Removal and installation of assembly of a steering column and sensor of an angle of rotation
12.5.5. Replacement of the lever of adjustment of a steering column
12.5.6. Removal and installation of the lock of ignition and blocking of a steering wheel
12.5.7. Removal and installation of the steering mechanism from GUR
12.5.8. Removal and installation of steering drafts, bipod and pendular lever
12.5.9. Removal and installation of the pump GUR
12.5.10. The angles of installation of wheels of the car - the general information
13. Body
14. Onboard electric equipment
15. Schemes of electric equipment



12-5-2-snyatie-i-ustanovka-rulevogo-kolesa-bloka-podushki-bezopasnosti.html

12.5.2. Removal and installation of a steering wheel, block of a safety cushion and its contact ring

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the rechargeable battery.
  1. Turn out two bolts.

At installation do not press cables.

Models to 03.1999 g of the issue.

 PERFORMANCE ORDER

  1. Separate the socket of an electrical wiring of the pyro (1), switch of a horn (2) and buttons of management on a steering wheel (3). Remove the block of a safety cushion and postpone its party face up.
  1. Establish a steering wheel in provision of the rectilinear movement (tags on a case of the steering mechanism and on the helmsman to a shaft have to coincide).
  1. Turn out a bolt, note the provision of a steering wheel of rather steering shaft and remove a steering wheel.

At a reversing of a bolt the lock spring (F) which holds a contact ring in neutral situation therefore for the purpose of preservation of operability of a contact ring it is not allowed to turn a steering wheel works until the bolt is not tightened.


  1. Installation of a steering wheel is made upside-down. The lock pin (1) has to enter a nest (2).
  1. If necessary adjust a contact ring. For this purpose press a spring (F on an illustration), define the neutral provision of a contact ring, having halved its whole revolution around an axis and release a spring. Pay attention to coincidence of tags (1).

Models from 03.1999 g of the issue.

 PERFORMANCE ORDER

  1. Separate sockets (1 and 2), remove the block of a safety cushion and postpone its party face up.
  1. Establish a steering wheel in the situation corresponding to the rectilinear movement of the car.
  1. Turn out a bolt and remove a steering wheel.
  1. Installation is made upside-down. Tags on a steering wheel and on the helmsman to a shaft have to coincide. Lock pins (1) have to enter nests (2).

All models (replacement of a contact ring)

 PERFORMANCE ORDER

  1. At the removed steering wheel uncover and disconnect the wire going on weight.
  1. Turn out screws and remove a contact ring.

The lead (1) can be removed only after the contact ring is fixed on a steering wheel, – squeeze both ends and take out a lead.

  1. Installation is made upside-down.


"previous page
12.5.1. Principle of work of GUR
following page"
12.5.3. Removal and installation of casings of a steering column